Tulaga Manaomia o le Polokalama mo PhotoRobot

O fa'amaumauga o lo'o i lalo o lo'o fa'amatalaina ai mana'oga o le faiga, fa'amatalaga mana'omia o masini, ma komepiuta fautuaina e fa'atino ai le PhotoRobot Controls Application. E aofia ai fa'amatalaga i le fetaui lelei o komepiuta, uaea USB, ma masini su'esu'e barcode talafeagai. Ina ia fa'atino le PhotoRobot Controls Application, e tatau ona fetaui lau komepiuta ma meafaigaluega ma nei fa'amatalaga fa'apitoa, o lo'o fa'amatalaina i lalo.

‍

‍

Choosing Your Platform

While PhotoRobot Controls runs on both macOS and Windows, PhotoRobot strongly recommends Apple-based systems for production use. We treat Apple as an integral part of the PhotoRobot system rather than an optional preference.

There are two reasons for this. Firstly, Apple offers a small, well-defined set of hardware configurations which we can fully test and validate every release against. This provides predictable, reproducible results in high-volume production. Secondly, Apple-based systems deliver an excellent cost-performance ratio, and a low total cost of ownership. Additionally, due to treating the computer as part of the delivered system, we minimize the need for internal IT intervention and third-party coordination on the customer’s side.

Windows remains fully supported, and we ship a Windows build. However, Windows is an open platform consisting of a very large number of hardware components and driver vendors. As a result, platform-specific operational issues can arise that originate outside of PhotoRobot software – most commonly, graphics-card and USB drivers. Resolving these issues is then the responsibility of the customer together with the relevant third-party vendor, as this hardware is not part of PhotoRobot’s supply. PhotoRobot supports its software; hardware-level and driver-level issues specific to a given Windows configuration must be handled with that component or driver vendor.

In short: Choose Apple to ensure the platform is a tested part of your system; choose Windows to meet corporate policy or preference, but plan for the occasional platform-specific issues that you will have to resolve with your hardware and driver vendors.

‍

‍

Ogatasi Faiga Faagaoioia

PhotoRobot Controls Application o lo'o avanoa mo fa'amatalaga nei o faiga fa'aoga:

• macOS 11 BigSur
• macOS 12 Monterey
• macOS 13 Ventura
• macOS 14 Sonoma
• macOS 15 Sequoia
• macOS Tahoe 26
• Windows 10 - 64bit
• Windows 11

‍

‍

Masini Fautuaina

MacOS

‍

Windows

‍

Note: Apple-based systems are recommended for optimal performance and stability with PhotoRobot software in production use. Refer back to the section “Choosing Your Platform” for more information.

‍

‍

Upegafesootai

PhotoRobot tilivaina atu i lana lava upega fesootai, e fesootai i le upegafesootai a le tagata faatau. E manaomia le fesootaiga i le Initoneti.

O le saoasaoa fautuaina i le initoneti o le 20/20 Mbps - mo le Cloud and Hybrid subscriptions.

O auaunaga nei / uafu e manaomia ona tatala i le initoneti:

• TCP, 443 (https), fafo atu o le
• TCP, 80 (http), fafo atu
• UDP, 53 (dns), i totonu, i fafo
• ICMP (ping), fautuaina

E manaomia le faaaogaina o nei tautua autu i luga o le Initoneti:

• *. photorobot.com - Auaunaga e Manaomia mo le PhotoRobot
• as-unirobot.azurewebsites.net - Tautua autu mo le toe faatoaagaina mai mo PhotoRobot, valaau i le galuega o le auaunaga i le aiga

Mo fa'amaumauga fa'apitoa i luga o le fa'atulagaina o feso'ota'iga, va'ai i le PhotoRobot Detailed Networking Prerequisites.

‍

‍

Komepiuta Fautuaina

O faiga faʻavae Apple o loʻo i lalo e fautuaina mo le faʻatinoga sili ona lelei ma le mautu, faʻatasi ai ma filifiliga e eseese e faʻatatau i lapopoʻa eseese o lau.

‍

• MacBook Air / Pro 15” / 16” (Feavea'i Lelei)

‍

• iMac 24” (Tau talafeagai, fofo uma-i-le-tasi)

‍

• Mac Mini (Tau talafeagai, avanoa mataʻitusi a isi vaega)

‍

All of the above computers perfectly meet PhotoRobot’s technical requirements. Detailed specifications then depend on expected cloud or local storage and processing. In general, an optimal choice will offer 16 - 32 GB RAM, and 256 - 512 GB SSD.

Note: The standard Apple Silicon configurations we recommend are fully sufficient for Controls. A higher core count does not improve the capture and editing performance – the additional cores in Max / Ultra chips aim to support heavy 3D and video rendering, not the PhotoRobot workflow. Thus, the recommended base configurations are also considerably more affordable. (Meanwhile, the high-core Mac Studio remains a great option, specifically for photogrammetry 3D reconstruction.) Be aware that other models may lead to issues, due to the screen being too small in size (MacBook Air, 14” MacBook Pro).

‍

‍

‍

Komepiuta Feso'ota'i ma Uaea USB

The PhotoRobot _Controls Drivers to connect cameras, robots, and lights support both macOS and Windows systems. However, remember that PhotoRobot strongly recommends using an Apple-based system for production use (see “Choosing Your Platform” for more information).

E ui lava o le faʻagasologa o ata e faia i le ao, e talafeagai le faʻaauupegaina o komepiuta mo le faʻagasologa o ata i se SSD (poʻo le Fusion Drive) ma se kata faʻataʻitaʻi e mafai ai ona faʻaaogaina le GPU.

Mo komepiuta e le'o fa'amoemoe mo le fa'agaioiga o ata, e mafai ona fa'aaogaina so'o se faiga fa'aoga ma se su'esu'e upega tafa'ilagi fa'aonaponei (matou te fautuaina Chrome).

Pe a faʻaaogaina le tele o mea puʻeata i le nofoaga e tasi (galulue faʻatasi – faʻataʻitaʻiga, ma se MultiCam system), e le fautuaina le faʻaaogaina o se USB HUB. Nai lo lena, matou te fautuaina le faʻafesoʻotaʻi saʻo o mea puʻeata i ports USB o le komepiuta. Afai e manaʻomia le faʻafesoʻotaʻi o mea puʻeata e sili atu nai lo ports o le komepiuta (mo se faʻataʻitaʻiga, o le iMac fautuaina e masani ona 4), e fautuaina le faʻaaogaina o hubs (maualuga le lelei) e faʻafesoʻotaʻi ai mea puʻeata e oʻo atu i le 2 i le port. A leai, e ova le uta o le USB bus o le mea puʻeata, ma e le faʻatuatuaina le faiga. Faʻamatalaga: Faʻamolemole faʻaaoga i taimi uma uaea USB maualuga le lelei ma le umi maualuga e 5 mita.

‍

Faʻamau Faʻamau Faʻamau

E mafai ona faʻaaogaina scanners barcode talafeagai ma PhotoRobot systems e:

• Fa'aofi otometi le code o le oloa i lona fa'ailoga i le PhotoRobot _Controls;
• Fa'aoso se fa'asologa o ata.

I se tulaga lautele, e mafai ona vaevaeina masini faitau barcode i masini uaea ma masini uaealesi. O masini faitau barcode uaea e fesoʻotaʻi i le USB o le komepiuta, ma e faʻatapulaʻaina e le umi o le uaea (e masani lava i le va o le 2 ma le 5 m). O masini faitau uaealesi e iai se faʻavae e faʻaaogaina e le USB e faʻatumuina ai pe fesoʻotaʻiga uaealesi i se komepiuta e ala i se USB dongle faʻapitoa. I se siosiomaga lelei e leai ni faʻalavelave ma le vaʻaia saʻo, o le mamao o scanners uaealesi e oʻo atu i le 100 m. I le faʻatinoga, peitaʻi, matou te fautuaina oe e faʻatatau i se mamao e 10 - 15 mita e faʻatatau i le siosiomaga (faʻalavelave, vaʻaia saʻo, faʻalavelave eletise, ma isi).

‍

‍

Fautuaina Fa'ata'ita'i Fa'amau Fa'amau

O fa'ata'ita'iga scanner barcode nei ua uma ona fa'ata'ita'iina i le fa'atinoga e PhotoRobot, ma e talafeagai fa'a-masini ma fa'a-eletise.

‍

‍

• Virtuos HW-855A - 2D (Faʻataʻitaʻiina ma Faʻaaogaina e PhotoRobot)
• Faitau barcode mo code 1D ma 2D (lelei mo QR)
• Scanner feaveaʻi ma le fesiitaiga o faʻamaumauga e leai se uaea ma se nofoaga e faʻatumu ai
• Faitau vave (60 mataʻitusi i le sekone) ma le sili atu le maaleale mo le faitauina o code ua faaleagaina poʻo code i luga o lau
• Ma'a e mafai ona sui e le tagata fa'aoga (ituaiga 18650)

‍

• Motorola LS2208 (Su'eina e PhotoRobot)
• Faitau barcode mo code 1D 
• Feso'ota'iga tumau o le faitau USB i le komepiuta e mana'omia
• E talafeagai mo siosiomaga vave, o le masini e malosi ma faʻataʻitaʻiina e tatalia paʻu
• Fa'amalama tioata fa'amalosi e le faigofie ona maosi ma tumau le lelei o le faitauina

‍

‍

• Honeywell Voyager 1202g Station (Su'eina e PhotoRobot)
• Fa'avae feso'ota'i i se komepiuta e ala i le USB; feso'ota'iga scanner ma le fa'avae e ala i le Bluetooth 
• Suʻesuʻega o paʻu paʻu 1D masani uma e mafai i le 10 mita mai le faʻavae
• Umi le ola o le maa ma le 12 itula o le fa'agaioiga fa'atuatuaina fa'afetai i le maa Li-Ion
• Suiga vave o le maa e aunoa ma le manaʻomia o meafaigaluega
• Fa'atulagaina otometi o feso'ota'iga ma mafai ona faitau fa'ailoga pa'u e le lelei – e aofia ai fa'ailoga pa'u ua fa'aleagaina pe puaoa
• Vaega mo le vave mauaina o se tagata faitau i le oomiina o se faamau i luga o le faavae – e tali mai le tagata faitau i leo pi ma emo

‍

Isi Faʻataʻitaʻiga Scanner Barcode (Leʻi Suʻesuʻeina e le PhotoRobot)

Mo fa'ata'ita'iga o isi fa'ata'ita'iga scanner barcode (e le'i fa'ata'ita'iina e le PhotoRobot), o lo'o i ai le Birch BZ-R01, po'o le Birch BS-115. Fa'amatalaga: O fa'amatalaga fa'ailoa o nei fa'ata'ita'iga e ogatasi ma mana'oga a le PhotoRobot, ae o fa'ata'ita'iga lava latou e le'i fa'ata'ita'iina i le fa'agaioiga ma le PhotoRobot. O nei fa'ata'ita'iga e mo na'o fa'ata'ita'iga, ma e tatau ona talanoaina ma se tekinisia fa'apitoa a le PhotoRobot mo le iloiloga pe a mana'omia e le tagata fa'atau.

‍

• Birch BZ-R01 (e leʻi faʻataʻitaʻiina i le faʻagaioiga ma PhotoRobot)
• Skena pa'u uaealesi CCD
• Tekonolosi “EZ Pair” mo le su'eina o barcode e o'o atu i le mamao e 100 mita mai le komepiuta – peita'i, o le mamao e a'afia e le si'osi'omaga

‍

‍

• Birch BS-115 (e leʻi faʻataʻitaʻiina i le faʻagaioiga ma PhotoRobot)
• Skena pa'u fa'amau leisa e uu i le lima
• Fesoʻotaʻiga i le komepiuta e ala i le uaea USB
• Fa'ailoaina o pa'u fa'ailoga 1D masani uma
• Fa'ata'ita'iga taugofie

‍

‍

Mea Pueata Fautuaina

Pe a filifilia se mea pu'eata fou mo se PhotoRobot system, va'ai i le lisi atoa o mea pu'eata fautuaina mo PhotoRobot Systems. O lenei ta'iala e fesoasoani i tagata fa'atau e filifili le mea pu'eata sili ona fautuaina po'o mea pu'eata mo le fa'aaogaina umi ma a latou PhotoRobot.

Taua: E fautuaina i taimi uma e fa'afeso'ota'i muamua PhotoRobot a'o le'i fa'atauina se mea pu'eata fou mo lau polokalama. E le gata i lea, ia manatua e na'o le lata mai mirrorless Canon mea pu'eata fa'ata'ita'iga e fautuaina mo otometi ata.

E ui lava, e pei o le fa'asa'olotoina o le PhotoRobot Controls App 2.5.4, o lo'o i ai le lagolago mo so'o se mea pu'eata e ala i le tu'ufa'atasia o mea pu'eata lona tolu. Ae ui i lea, manatua o le fa'aaogaina o mea pu'eata feavea'i talafeagai i luga o le Wi-Fi po'o le feso'ota'iga uaea e mafai lava ona mafua ai ni fa'afitauli. O fa'afitauli e aofia ai le motusia soo o feso'ota'iga (aemaise lava ona o le taimi), ma fa'afitauli i le uaea po'o le umi o feso'ota'iga. Afai e te fa'aaogaina se mea pu'eata iPhone e ala i le PhotoRobot Touch, e leai ni fa'afitauli e tula'i mai. Ina ia siaki le ogatasi o Canon uma lagolagoina ma 3rd pati mea pueata fa'ata'ita'iga, va'ai PhotoRobot Compatible Cameras mo fa'amatalaga.

Fa'aaliga: Ina ia malamalama atili i le a'afiaga o le iugafono mea pu'eata ma le filifiliga o tioata, va'ai i le PhotoRobot's Guide on Understanding Camera Resolution. Mo le lagolago a le tagata fa'aaoga i le fa'atulagaina ma le fa'afeso'ota'i o se mea pu'eata talafeagai, va'ai i le tusi lesona lagolago PhotoRobot Camera Configuration.